Please review and accept our Privacy Policy before signing up for the newsletter. Unread posts All posts Latest activity New vehicle showcases New showcase comments Thread starter SandyEggoSi Start date Jan 25, 2018 Tags aftermarket rims stock suspension wheels First Name Dave Joined Dec 24, 2017 Messages 113 Reaction score 76 Location San Diego, CA Car(s) 2017 Civic Si Rallye Red
I find it difficult to credit the coach moving down the hill with 20,000 - 40,000 lbs of motorhome pressing the jack pads into the earth. That assumes the jacks are rated for the full coach weight and don't break under the load. My 36,000 lb coach had 4 x 16,000 lb jacks, so I wasn't too worried. Back in the day some coaches had poor frame rigidity, especially up front, so the front cap and windshield frame would often twist if the front wheels came off the ground. My '96 Southwind (F53 chassis) was like that and I avoided ever lifting the front to even barely touching cause the windshield would start to move. My 2002 W22 chassis coach didn't seem to have any problem with that but I was still careful. My 2004 DP was stable as a mountain no matter how much it was jacked. Spent many a summer at my brothers home in SW PA with wheels off the ground. He lives on a hill side and the 2012 Tour never had a problem.
.
This was clearly made by someone who has never had to get two carburetors to work simultaneously or two flutists.
Suspension travel of 3’’Light and high strength aluminum (2024)Solid design for off-airport use (tested at 4G)
Riser Recliners and Furniture High Seat / Nursing Home Chairs / Furniture Riser Recliner Chairs
Looking good fellow Sandy Eggan! haha. Wish they came in other colors like a gunmetal/anthracite. Joined Jan 14, 2018 Messages 15 Reaction score 10 Location Sactown Car(s) CivicX
Curve & Curve L are a high quality, ergonomic push rim designed and made in Germany. These are available in two sizes: ‘Curve L’ for a larger hand, or ‘Curve’ for smaller hands. Designed for wheelchair users with complete hand function.
Fittings, unless noted, are made from hot-rolled, pickled and oiled steel plates, bar, strip or coil, and conform to one or more of the following specifications: ASTM specifications A575, A576, A635, A1011 SS GR 33, A1011 HSLAS GR 45 or A36. All fittings meet or exceed physical properties of ASTM A1011 GR 33. The pickling of the steel produces a smooth surface free from scale. Many fittings are also available in stainless steel, aluminum and fiberglass. Consult factory for ordering information. Green Powder Coat (GR), conforming to commercial standards for Powder Coating Electro-galvanized (EG), conforming to ASTM B633 Type III SC1 Hot-dipped galvanized (HG), conforming to ASTM A123 or A153 Plain (PL) Unistrut Defender (DF), conforming to ASTM A1059 or A1046
Walking Aids Four Wheeled Walkers / Rollators Three Wheeled Walkers / Tri Wheel Walking Frames Walking Sticks and Crutches
A wide variety of controls and PC parts for electrical engineers including Controls, Powers, PC parts and more. Control PC Parts Terminal Blocks Receiving and Distributing Electricity Power Supplies Communication Boards/Cabinet Parts Inspections/Measurements Circuit Board Parts Environment-Resistant Equipment Mechanical Devices Clock/Timing Devices
Set in the Nottinghamshire countryside, Loopwheels HQ is surrounded by rutted fields, forests and coarse roads – nigh-on the perfect environment to test out suspension wheels!
And it's not like I have some high dollar customer sport chair, either. I use a "Breezy". Street price of $575. About as cheap as you an go. (https://www.quickie-wheelchairs.com/Breezy-Wheelchairs/Breezy-Lightweight-Wheelchairs/Breezy-600-Lightweight-Wheelchair/2403p) And the only modification I made was to cut grooves into the solid rubber tires. (They come smooth as a babies butt. That REALLY doesn't work in snow.) Grunchy January 31, 2018 01:30 AM Reason January 31, 2018 05:28 AM
The arm may be broadened into a V shape with two pivots, either side by side or with the inner pivot slightly behind the front one - a semi-trailing arm. Trailing arms are usually found at the rear only. A trailing-arm suspension on a rear-wheel-drive car. The arm is attached to the rear wheel hub and broadens into a V whose two arms extend forward to pivot on the frame. The differential is fixed to the frame and the drive shafts have universal joints.
Looks to me like it is a rigid rim and all the suspension takes place within the three loops of carbon inside. No worries about wheels changing shape or tires blowing off. The axle just moves off center during compression. ChrisC on April 14th, 2013 - 10:39pm ChrisC on April 14th, 2013 - 10:40pm jimmythefish on April 14th, 2013 - 11:00pm
The sale of Bacchetta Cycles was in the news since our last webcast. We have former CEO Mark Swanson and new owner Dana Lieberman with us for interviews. Along with the rest of the recumbent news is Honza Galla.
It’s not often I get a chance to review articles of clothing, but when someone sent me an email, talking about how good a pair of shorts were, to the point that both he and his wife have bought more than two pairs for each, I decided to take a look. I’m talking about the “Uprising” from a company called elevenpine. Read More » The Ultimate ICE Sprint X Tour Posted on August 31, 2020 by Larry Varney
Surprised at the baseless negativity this morning. Wait, no, I’m not. Maybe it’s not the simplest suspension solution, but a cool alternative when everything else is homogenizing. bazookasean on May 20th, 2016 - 9:48am