Looks great...thanks! Those are very clear, telling pics...no fear about getting 20" wheels now. I appreciate it. Not to mention the tires are significantly cheaper than 19's. What I was referring to before was a generalization with 19" wheels as opposed to your concern of having 20". When it comes to how a car looks with aftermarket wheels, it really depends on a combination of the offset, size and width. A combination of the three as compared with stock specs will either give you more positive or negative camber and therefore can change the wheel gap. Before you make your purchase, I recommend learning how the dimensions of your setup will change based on the wheels that you want. This will give you a better understanding of their affect on your wheel gap. The pics i've seen so far have been fine so I doubt there will be a huge change but nonetheless, your best bet would be finding a picture of a stock suspension car with the same sized wheels and offsets that you want.
[Hot Item] Spring loaded wheels, SA63SP-5''/6''/8'', Caster Wheels, China, Factory, Suppliers, Manufacturers
.
'I've now been working on making it a product for 4 years, and we've made 40 wheels and 200 springs to get it right.
Privacy Policy(Open in a new window)Do Not Sell My Personal Info(Open in a new window)Cookie Settings
Barel sees bikers embracing the SoftWheel. “Our wheel will enable bikers to ride faster and more smoothly,” he said. “In standard wheels, about 30 percent of propulsion energy is reserved for suspension, even if that suspension isn’t necessary at a specific time. With our system, suspension can be turned on and off as needed, reserving more energy for speed.”
When one wheel moves up it pulls up one end of the bar and the other end pulls up the other wheel, keeping the car level.
The Hovertrax has no learning curve and requires no skills to use, which is good because you can bet that if I'm too lazy to walk myself down the street or hallway, I am definitely too lazy to learn how to use a complex...
[Hot Item] Spring loaded swivel casters, SA65SP-6''/8'', Caster Wheels, China, Factory, Suppliers, Manufacturers
The monstrous 25-foot-tall Caterpillar 797F mining truck with its 13-foot-tall standard pneumatic tires
TRX is the first Ram truck to be equipped with Launch Control with Launch Assist, which regulates engine RPM and monitors wheel slip feedback in order to always achieve the fastest possible acceleration rate.
36cm x 41cm (14″x16″)41cm x 41cm (16″x16″)43cm x 41cm (17″x16″)46cm 41cm (18″x16″)46cm x 46cm (18″x18″)
Thats another issue im going to have is picking a tire size, do you think 1.5 is enough to be flush? It seems my fender gap is more prominent in the front and the back is slightly lower, could be my worn out springs showing. Also if you could recommend a tire that would go well with a 1.5 lowering (if thats enough) to go over 15X7s
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
I might eventually drop it. You have remember though, the roadsters sit atleast a half inch lower than the coupes to begin with (stock). Here's mine on 19's. I'll probably cut down the spring seats to level it up a bit in the rear. Use a slightly taller tire. That helps alot. Mine are 275/35/19 and 285/35/19 and I love the way it looks on the stock suspension. Last edited by Firehawk; 02-26-2007 at 03:34 AM. with my roadster, i went from Eibach, to Hotchkis, and now waiting for Tein Htech to come in. I think Htech will be the perfect drop for me, LOL Even with 35 sidewall tires, the gap in stock suspension is horrible. There are a lot of good points that have been made in this thread. I think a big factor in your decision will be really the road conditions in your area. Lots of changes in slopes that cause you to bottom out would not be a good thing for a lowered vehicle. The cars I have seen here look quite good, mostly because they have either 19s or dubs on them.
[Hot Item] Spring damping caster wheels, SA61SP-4''/5''/6''/8'', Caster Wheels, China, Factory, Suppliers, Manufacturers
The most loop-the-loops in a Hot Wheels track is 10 and was achieved by Rohan Dayal and Rahul Dayal (both India) in Mumbai, Maharashtra, India, on 7 April 2021. It took Rohan and Rahul three days to build the adjustable angle wooden platform and assemble the entire track of 10 loops over it. Two people were involved in the project. Rohan Dayal and his younger brother Rahul Dayal. "Testing was initially with few loops and as we increased the loops and the length of the track, the project became challenging. Since the track became long it needed to be supported on a firmer wooden platform. The longer the platform, the greater was the weight and bending in the center. This needed strengthening of the platform. This was the initial challenge." While testing the brothers found that the journey of the car through the loops depended greatly on the angle of the platform. To facilitate variable angles they had to construct an adjustable wooden leg support. By adjusting the leg support during testing they arrived at the best angle which gave them the breakthrough that they could achieve the target. The project cost approximately INR 3500 ( approximately £35). The cost was less as the brothers already had collections of Hot Wheels cars and track and only had to purchase the remaining missing track pieces. The plywood used for the platform was upcycled from scrap. There were a numbe rof challenges faced by the pair. As the number of loops increase, the project became challenging in terms of scale. The length of the platform, it's weight, and height also presented difficulties in handling. The speed of the Hot Wheels car increases as it descends from greater heights causing the car to lose balance. Despite all these difficulties the pair think they could attempt to increase the loops by a further one or two in the future. "Since a young age of around 12 years, I would try to do small projects like making a wooden toy car or cricket bat. Later as I grew I would do some small household repair works. For all this, I would use my Dad’s tools. As a child, I liked playing with toy cars. I would make my wooden toy car and make it slide on sloping surfaces. During this time I was gifted with Hot Wheels cars and tracks which came with super smooth cars and steep sloping tracks. Soon I had a good collection of it. Recently I came to know about the Guinness World Record of 8 loops and decided that I can better the record. The Guinness World Records titleholder would be the best thing I would have ever got. It would also mean that records are an inspiration to do better and create greater records. It would be a proud moment for both me and my family."
A wide variety of tools and supplies used in processing including Machine Tools, Measurement Tools, Grinding and Polishing Supplies and more. Machine Tools Measurement Tools / Measuring Equipment Electric Discharge Tools Products for Welding Abrasives for Grinders Products for Cutting Hand Tools Electric Tools Pneumatic Tools Chemical Products Repair Agents and Adhesive Soldering and Anti-Static Supplies