These air shocks are tuneable to give you whatever level of tire deflection you choose, from super-firm to softer and squishier than a regular deflated tire can handle. Likewise, you can design in whatever degree of lateral flex suits your application, and even whatever level of torque flex you'd like, which allows the wheel to flex a little on the axle before it turns. This allows it to act as a soft torque coupler and gives a touch more traction in very difficult circumstances before the wheel spins, as well as slightly isolating the drive train from damaging torque forces in the rough stuff.
Design load data, where shown, is based on the ultimate strength of the connection with a safety factor of 2.5, unless otherwise noted.

In a Globe story this February, reporter Eric Moskowitz noted that Boston fills approximately 19,000 potholes in an average winter, and that the city has gone as far as developing a new app, called Street Bump, that attempts to give drivers the ability to instantly notify City Hall when a new crater appears. And that's just the city of Boston. Do the math and consider how many gaping holes have appeared in the New England region after last winter's prodigious snowfall.
Seems like a lot of the aftermarket wheels are on lowered Supras, anybody here running aftermarket wheels with stock suspension? Unfortunately with my driveway and roads, lowering may not be an option due to the possibility of scraping. I feel others may be in the same boat so this may be a helpful thread. Please share photos and specs of your aftermarket wheels/tires with stock suspension! First Name Sam Joined May 4, 2020 Messages 167 Reaction score 158 Location Houston Car(s) 2021 A91, 2008 S2000 CR, tow pigs First Name Dan Joined Oct 5, 2020 Messages 64 Reaction score 107 Location OH, US Car(s) '21 Supra 3.0 premium Gram Lights 57CR in gloss black: 19x9.5 +25, 19x10.5 +35 stock tires, stock suspension. Doubt I'll ever change it, but if I do, it'll be a minimal drop because I'm not getting any younger First Name Kyle Joined Jun 22, 2020 Messages 243 Reaction score 123 Location CA Car(s) 2020 A90 GR Supra, 1996 NA Miata, 2014 Camry SE but none the less, here is my contribution. still trying to figure out my fitment tho.. i dont think im going to lower my car (due to my driveway, which i already scrape on, and my daily drives) theyre ESR SR01 19x9.5 +22 front and 19x10.5 +22 on rears. I had to run a 12mm spacer in front to clear the caliper (which i thought it was going to clear, but sadly was wong) which made my rear fitment a bit weak compared to the front. so i had to compensate with a little 5mm spacer on the rear (still not sure whether to run a 5mm or 10mm spacer on the rear, i feel like 10mm would be really pushing it and will rub badly.) First Name Steve Joined Nov 21, 2020 Messages 593 Reaction score 574 Location Beaufort South Carolina Car(s) 2021 a91 edition Supra 2016 Lexus rc f BMW 435I imo Wheels should not poke out from the fenders...makes the car look like a 4 wheel drive...but each his own If so why not change the barrels for a more flush fit? Or were you going for a poke look? First Name Kyle Joined Jun 22, 2020 Messages 243 Reaction score 123 Location CA Car(s) 2020 A90 GR Supra, 1996 NA Miata, 2014 Camry SE If so why not change the barrels for a more flush fit? Or were you going for a poke look? i was going for a more "flush" look and its the only offset they offered. I thought i was going to clear upfront, and worried more with the rear. but it turned out the other way around.. and since the front poked out, i was trying to compensate on the rears. but i dont mind "a little" poke just not too much. oh well at least it looks decent