The most loop-the-loops in a Hot Wheels track is 10 and was achieved by Rohan Dayal and Rahul Dayal (both India) in Mumbai, Maharashtra, India, on 7 April 2021. It took Rohan and Rahul three days to build the adjustable angle wooden platform and assemble the entire track of 10 loops over it. Two people were involved in the project. Rohan Dayal and his younger brother Rahul Dayal. "Testing was initially with few loops and as we increased the loops and the length of the track, the project became challenging. Since the track became long it needed to be supported on a firmer wooden platform. The longer the platform, the greater was the weight and bending in the center. This needed strengthening of the platform. This was the initial challenge." While testing the brothers found that the journey of the car through the loops depended greatly on the angle of the platform. To facilitate variable angles they had to construct an adjustable wooden leg support. By adjusting the leg support during testing they arrived at the best angle which gave them the breakthrough that they could achieve the target. The project cost approximately INR 3500 ( approximately £35). The cost was less as the brothers already had collections of Hot Wheels cars and track and only had to purchase the remaining missing track pieces. The plywood used for the platform was upcycled from scrap. There were a numbe rof challenges faced by the pair. As the number of loops increase, the project became challenging in terms of scale. The length of the platform, it's weight, and height also presented difficulties in handling. The speed of the Hot Wheels car increases as it descends from greater heights causing the car to lose balance. Despite all these difficulties the pair think they could attempt to increase the loops by a further one or two in the future. "Since a young age of around 12 years, I would try to do small projects like making a wooden toy car or cricket bat. Later as I grew I would do some small household repair works. For all this, I would use my Dad’s tools. As a child, I liked playing with toy cars. I would make my wooden toy car and make it slide on sloping surfaces. During this time I was gifted with Hot Wheels cars and tracks which came with super smooth cars and steep sloping tracks. Soon I had a good collection of it. Recently I came to know about the Guinness World Record of 8 loops and decided that I can better the record. The Guinness World Records titleholder would be the best thing I would have ever got. It would also mean that records are an inspiration to do better and create greater records. It would be a proud moment for both me and my family."
The spokes on a standard spoked wheel hold it in tension. If the spokes lose tension, they start to break and the rim will buckle. A Loopwheel is not held in tension by its springs therefore the rim is strong, double-walled, and less likely to suffer from buckling or fracture at the rim.

Seems like a lot of the aftermarket wheels are on lowered Supras, anybody here running aftermarket wheels with stock suspension? Unfortunately with my driveway and roads, lowering may not be an option due to the possibility of scraping. I feel others may be in the same boat so this may be a helpful thread. Please share photos and specs of your aftermarket wheels/tires with stock suspension! First Name Sam Joined May 4, 2020 Messages 167 Reaction score 158 Location Houston Car(s) 2021 A91, 2008 S2000 CR, tow pigs First Name Dan Joined Oct 5, 2020 Messages 64 Reaction score 107 Location OH, US Car(s) '21 Supra 3.0 premium Gram Lights 57CR in gloss black: 19x9.5 +25, 19x10.5 +35 stock tires, stock suspension. Doubt I'll ever change it, but if I do, it'll be a minimal drop because I'm not getting any younger First Name Kyle Joined Jun 22, 2020 Messages 243 Reaction score 123 Location CA Car(s) 2020 A90 GR Supra, 1996 NA Miata, 2014 Camry SE but none the less, here is my contribution. still trying to figure out my fitment tho.. i dont think im going to lower my car (due to my driveway, which i already scrape on, and my daily drives) theyre ESR SR01 19x9.5 +22 front and 19x10.5 +22 on rears. I had to run a 12mm spacer in front to clear the caliper (which i thought it was going to clear, but sadly was wong) which made my rear fitment a bit weak compared to the front. so i had to compensate with a little 5mm spacer on the rear (still not sure whether to run a 5mm or 10mm spacer on the rear, i feel like 10mm would be really pushing it and will rub badly.) First Name Steve Joined Nov 21, 2020 Messages 593 Reaction score 574 Location Beaufort South Carolina Car(s) 2021 a91 edition Supra 2016 Lexus rc f BMW 435I imo Wheels should not poke out from the fenders...makes the car look like a 4 wheel drive...but each his own If so why not change the barrels for a more flush fit? Or were you going for a poke look? First Name Kyle Joined Jun 22, 2020 Messages 243 Reaction score 123 Location CA Car(s) 2020 A90 GR Supra, 1996 NA Miata, 2014 Camry SE If so why not change the barrels for a more flush fit? Or were you going for a poke look? i was going for a more "flush" look and its the only offset they offered. I thought i was going to clear upfront, and worried more with the rear. but it turned out the other way around.. and since the front poked out, i was trying to compensate on the rears. but i dont mind "a little" poke just not too much. oh well at least it looks decent
Without a suspension system, the car’s wheels would hit a bump and move up and down perpendicular to the road surface. This vertical energy would be transferred to the car’s frame, which would pull the wheels away from the road before gravity takes over and slams the car down. The suspension system must be finely tuned using a combination of springs and shock absorbers to reduce these effects for a comfortable and smooth ride.