Currently, this is just a concept with renderings, no prototype or production is planned.
Seems like a lot of the aftermarket wheels are on lowered Supras, anybody here running aftermarket wheels with stock suspension? Unfortunately with my driveway and roads, lowering may not be an option due to the possibility of scraping. I feel others may be in the same boat so this may be a helpful thread. Please share photos and specs of your aftermarket wheels/tires with stock suspension! First Name Sam Joined May 4, 2020 Messages 167 Reaction score 158 Location Houston Car(s) 2021 A91, 2008 S2000 CR, tow pigs First Name Dan Joined Oct 5, 2020 Messages 64 Reaction score 107 Location OH, US Car(s) '21 Supra 3.0 premium Gram Lights 57CR in gloss black: 19x9.5 +25, 19x10.5 +35 stock tires, stock suspension. Doubt I'll ever change it, but if I do, it'll be a minimal drop because I'm not getting any younger First Name Kyle Joined Jun 22, 2020 Messages 243 Reaction score 123 Location CA Car(s) 2020 A90 GR Supra, 1996 NA Miata, 2014 Camry SE but none the less, here is my contribution. still trying to figure out my fitment tho.. i dont think im going to lower my car (due to my driveway, which i already scrape on, and my daily drives) theyre ESR SR01 19x9.5 +22 front and 19x10.5 +22 on rears. I had to run a 12mm spacer in front to clear the caliper (which i thought it was going to clear, but sadly was wong) which made my rear fitment a bit weak compared to the front. so i had to compensate with a little 5mm spacer on the rear (still not sure whether to run a 5mm or 10mm spacer on the rear, i feel like 10mm would be really pushing it and will rub badly.) First Name Steve Joined Nov 21, 2020 Messages 593 Reaction score 574 Location Beaufort South Carolina Car(s) 2021 a91 edition Supra 2016 Lexus rc f BMW 435I imo Wheels should not poke out from the fenders...makes the car look like a 4 wheel drive...but each his own If so why not change the barrels for a more flush fit? Or were you going for a poke look? First Name Kyle Joined Jun 22, 2020 Messages 243 Reaction score 123 Location CA Car(s) 2020 A90 GR Supra, 1996 NA Miata, 2014 Camry SE If so why not change the barrels for a more flush fit? Or were you going for a poke look? i was going for a more "flush" look and its the only offset they offered. I thought i was going to clear upfront, and worried more with the rear. but it turned out the other way around.. and since the front poked out, i was trying to compensate on the rears. but i dont mind "a little" poke just not too much. oh well at least it looks decent

Loving this well made Schwinn! Have many miles of very hard riding on it now and it is holding up well. Zero issues and still functioning perfectly. There is a slight amount of seepage at the front forks but that is normal. I have just about worn out the tires but that is after a lot of miles, most of which were ridden on rough rocky roads with zero flats. Overall this bike is a winner. Well worth the current price.
looking to get the same size and offset wheel and tires for stock Si (not planning to lower), will it work without rolling fenders? looking to get the same size and offset wheel and tires for stock Si (not planning to lower), will it work without rolling fenders? I think so. The minor hand pull I did front and rear was only for aesthetics. The rear wheels definitely gain a lot of neg camber when compressed so shouldn't be an issue there and the front should be fine as well. What you may want to take into account is the "rim protector" on certain tires is fairly aggressive on some (Continental Extreme Contact Sport) but not existent on others (Hankook V12 Evo2). If any amount of poke bothers you, then try to look at pictures of wheels and look for that. But I would again say that is more for aesthetics. But I would prob look into removing the locating pin on the upper strut mount up front first and adding in that little bit of neg camber for more clearance first.