We put up with a lot from our pneumatic tires, from punctures and blowouts, to slashings and the certainty of relatively frequent, inconvenient replacements and giant piles of waste rubber. The current technology seems well overdue for a revolutionary overhaul, if you'll pardon the pun, and yet despite dozens of fascinating attempts to reinvent the wheel, nothing seems to have found traction yet. Boy, I'm on a roll here.
Customer Service Shipping Information Contact Us EPC Quotations/Estimates Wheelchair Measurement Guide Terms & Conditions VAT Exemption We've Moved
.
Loopwheels ($300+) give you that comfortable ride you’ve been looking for. If you have a folding commuter bike like a Dahon Mu Uno, which doesn’t come with its own suspension system, then you neeed to take a look at Loopwheels. These suspension wheels allow you take bumps, curbs, and potholes in comfort with reduced vibration. The Loopwheel doesn’t fit every bike. It’s a 20″ wheel with specific clearance requirements, so check out their Kickstarter page to see if your bike is an option.
The Loopwheel system uses springs instead of spokes, giving the wheel built in suspension.
When you provide the correct make, model (and version if applicable), and year information about the vehicle we do verify bolt pattern, TPMS sensors and lug nuts (these items we guarantee fitment).
Note: When used for mechanical supports, load capacities of brackets, fittings and other supporting elements should be in compliance with the American Standard Code for Pressure Piping. Clamps are designed to be used with W, M, S & HP Shape beams, Standard C & Misc. MC Channels, Angles & Structural Tees. Clamps must be used in pairs where indicated. For beam clamps with HG finish, standard hardware is EG finish. For optional stainless steel hardware, please contact the factory for availability.
Hi we are new to a air ride equipped motorhome and are wandering if it is ok to lift the wheels off the ground with the Jack's when leveling on those unlevel sites, the chassis is a Freightliner XC and it seems like the air bags are really stretched if the wheells and everything are pulling down on them in this situation ... We just do not want any damage to the system. Your input would be appreciated thanks The weight of the axle pulls down on the air bags but the weight of the front axle assembly is supported by the length of the shocks. When the shocks become fully extended, air bags, leaf or coil springs, that's when the front axle assembly quits moving down. I'm with everyone that doesn't like the looks of wheels in the air, but it doesn't hurt anything and I have done it. Think about this: The only way your motorcoach can roll away is if it's on the wheels. If it's up on the jacks, it can't roll. A good backhoe operator will hike the rear tires (where the brakes are) up in the air to get it up on the hydraulics where it is solid and stable, before operating. Sometimes they raise the front tires up with the bucket. Ever seen a mobile construction crane? First thing they do is raise all the tires up off the ground to get the unit level and stable before operating. I'm not saying to lift your coach that way, but it's not the big deal that some people try to make it sound like. On my Freightliner with the stiff rear end and V-Ride, if I lift one side a couple inches, the duals will come off the ground. Not a big deal because the jack won't roll.
Goolsky Motor and Explosion Proof Honeycomb Structure Anti-Skid Wheel Tire Set for M365 Electric Scooter
Our website requires JavaScript to be enabled to work properly. Please enable JavaScript.
Now consider the car that it replaces. The first-generation 2009 Chrysler 300C AWD was equipped with 18-inch wheels at the largest. A set of four 225/60R18 Continental ContiProContact ContiSeal tires is available from TireRack.com for $596, not including mount, balance, disposal, or alignment at your local retailer.
Maybe I’m wrong but wouldn’t the wheel react differently every time you hit the same obstacle depending on how the shocks are pointed? Bartthebikeman on May 20th, 2016 - 2:58pm
As a comparison, consider the 1995 Corvette ZR-1, an ultra-high performance, 405 horsepower Corvette of which 527 units were sold. It came equipped with 17-inch wheels and tires. The front tires were 275/45R17s, meaning they were three-quarters of an inch thicker, had the same height sidewall, but were smaller than the Taurus by two inches in diameter.
suspension...then rims...n +40 isnt that low of an offset...anways low offset or not u can always get a camber kit n make them fit... n if u wana do it rite the 1st time...get coilovers...dont get springs...every1 who gets springs eventually get coilovers...thats bout $350 wasted rite there... i had my wheels for about a year before i had the suspension and i kept it off the car because i knew it would look terrible without the drop.
A pair of shock absorbing loopwheels with integral suspension,to help you push over uneven streets, rough tracks, grass and gravel paths with less effort. The carbon springs in these wheels give you e...
If you have questions/comments for our guests and can’t watch live please feel free to respond to this post and I’ll try to ask for you during the show. And that’s not the only news – check out that rear hub in the photo! For more information, contact your nearest ICE dealer, and/or visit the ICE website: https://www.icetrikes.co/
Founder Sam Pearce describes his design idea: “In 2007 my idea of a wheel with tangential suspension was born when I was sitting at Eindhoven airport waiting for a flight. I saw a mother pushing her child in a buggy. The front wheels hit a slight kerb and the child jolted forward because of the impact. I asked myself why a wheel couldn’t have suspension inside it, so it would soften an impact from any direction. I sketched the idea in my notebook, got on my flight, and didn’t think much more about it for a couple of years.”
i think it depends on what your unique situation is. if there are rims you really like, buy them and work around it. plus, if your facing winter every year, you do not want to be dropped too much, you'll be sliding all over since you will have a lower center of gravity and have more of a grip demand on your tires. if you drop it three inches, now you need to stick with a really high offset, so that will limit your wheel choices. i think it works the same way no matter what you do-suspension first will limit your wheel options...wheels first will limit your suspension options. do you want to be scraping low with small wheels, or keep it practical with bigger wheels, it's your choice!!